PIC16F737/747/767/777 Configuration Word Register 1 (ADDRESS 2007h) CP CCPMX DEBUG _ _ BORV1 BORV0 BOREN MCLRE FOSC2 PWRTEN WDTEN FOSC1 FOSC0 bit 13 bit 0   bit 13: CP: Flash Program Memory Code Protection bits    1 = Code protection off    0 = 0000h to 1FFFh code-protected for PIC16F767/777 and 0000h to 0FFFh for PIC16F737/747 (all protected) bit 12: CCPMX: CCP2 Multiplex bit    1 = CCP2 is on RC1    0 = CCP2 is on RB3 bit 11: DEBUG: In-Circuit Debugger Mode bit    1 = In-Circuit Debugger disabled, RB6 and RB7 are general purpose I/O pins    0 = In-Circuit Debugger enabled, RB6 and RB7 are dedicated to the debugger bit 10-9: Unimplemented: Read as '1' bit 8-7: BORV<1:0>: Brown-out Reset Voltage bits 11 = VBOR set to 2.0V 10 = VBOR set to 2.7V 01 = VBOR set to 4.2V 00 = VBOR set to 4.5V bit 6: BOREN: Brown-out Reset Enable bit BOREN combines with BORSEN to control when BOR is enabled and how it is controlled. BOREN:BORSEN: 11 = BOR enabled and always on 10 = BOR enabled during operation and disabled during Sleep by hardware 01 = BOR controlled by software bit SBOREN - refer to Register 2-8 (PCON<2>) 00 = BOR disabled bit 5: MCLRE: MCLR/VPP/RE3 Pin Function Select bit 1 = MCLR/VPP/RE3 pin function is MCLR 0 = MCLR/VPP/RE3 pin function is digital input only, MCLR gated to '1' bit 3: PWRTEN: Power-up Timer Enable bit 1 = PWRT disabled 0 = PWRT enabled bit 2: WDTEN: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 4, 1-0: FOSC2:FOSC0: Oscillator Selection bits 111 = EXTRC oscillator; CLKO function on OSC2/CLKO/RA6 110 = EXTRC oscillator; port I/O function on OSC2/CLKO/RA6 101 = INTRC oscillator; CLKO function on OSC2/CLKO/RA6 and port I/O function on OSC1/CLKI/RA7 100 = INTRC oscillator; port I/O function on OSC1/CLKI/RA7 and OSC2/CLKO/RA6 011 = EXTCLK; port I/O function on OSC2/CLKO/RA6 010 = HS oscillator 001 = XT oscillator 000 = LP oscillator Configuration Word Register 2 (ADDRESS 2008h) _ _ _ _ _ _ _ BORSEN _ _ _ _ IESO FCMEN bit 13 bit 0   bit 13-7: Unimplemented: Read as '1' bit 6: BORSEN: Brown-out Reset Software Enable bit Refer to Configuration Word Register 1, bit 6 for the function of this bit. bit 5-2: Unimplemented: Read as '1' bit 1: IESO: Internal External Switchover bit 1 = Internal External Switchover mode enabled 0 = Internal External Switchover mode disabled bit 0: FCMEN: Fail-Safe Clock Monitor Enable bit 1 = Fail-Safe Clock Monitor enabled 0 = Fail-Safe Clock Monitor disabled       Configuration Word:
Any questions? Continue to the Contact Page //